Installation telephonie

All Packages for the complete set of Telephone System, reaching to site shall be identified as per package list. Where auxiliaries are shipped loose, these will be identified and checked against the dispatch documents.

Special attention shall be paid to the instruments and monitoring devices supplied loose. All materials received at site shall be inspected and ensured that the materials are as per approved material submittal, shop drawing and single line diagram.

Tips and Warnings. Things You'll Need. Related Articles. Article Summary. Part 1. Choose a spot for the new phone jack.

Assess your room and think about the best path for the phone wires. If you need a new phone jack on the opposite side of the room from your existing jack, will it be possible to run the wires along your baseboards? Figure out how much new wire you need. Measure the distance from the old jack to the spot where the new one will be installed. Go to the hardware store and purchase the amount of wire you will need. If your new jack is going to be located several feet from the old one, you should also buy fasteners that are made for keeping the wire in place along walls and baseboards.

Choose a new jack. These types of jacks are simply affixed to your baseboard or wall, with minimal drilling required. Affix the new jack to the spot you have chosen. Some jacks come with adhesive backing and simple mounting instructions. Others may need to be screwed into the wall. Depending on the type of wall you have, this may be accomplished either with a screwdriver and a bit of muscle or with a small drill. Ensure that your jack is not installed at a crooked angle by using a level to help you line up the jack with your floor or baseboard.

Attach telephone wire to the old jack. Open the casing, or unscrew the plating, on the old jack. Loosen the screws that secure the red, green, yellow and black telephone wires. As necessary, trim damage from the old wires and strip the insulation from the tips. Strip the insulation from the tips of the new wires, too.

Twist the tips of the new wires with the tips of the old wires according to color: red to red, green to green, yellow to yellow, and black to black. Replace the twisted portions of the wires under the screws in the jack, and tighten the screws.

Thread the new wire through the hole in the phone jack casing, and screw the casing back to the wall. Run the wire from the old jack to the new jack. Using the path you mapped out in your original plan, run the new wire to the new jack. If you are running the wire along baseboards or up walls, use the fasteners you bought at the hardware store to secure it neatly in place.

Attach telephone wire to the new jack. Strip the insulation from the tips of the four wires. Loosen the screws on the back of the new jack, and affix the red, green, yellow, and black wires in their correct color-coded places.

Tighten the screws. Finish installing the new jack. Place the cover on the jack and screw it on. Reconnect the phone line and test your work. Return to the NID box and reconnect your phone line. Go back inside and test it by plugging in your phone or DSL cable. If you have a dial tone and your internet works, your task is complete. Part 2. For example, if your old jack is a standard rectangular wall plate, it will be easiest to install a new jack that looks very similar.

If you plan to attach your telephone to the wall, make sure you buy a wall mount jack, rather than a flush jack. A wall mount jack juts out from the wall, providing a structure on which to mount your telephone. A flush jack lies flat against the wall, allowing you to plug in your phone, but not mount it. Baseboard jacks are small plastic or metal boxes that are affixed to your baseboard, with the jack opening on the bottom edge of the box.

The NID has two sides: one for the phone company, and one for customers. Now your phone line is disconnected from the outside network. Part 3. Download the currently supported versions of Asterisk and various Asterisk-related open source projects. Asterisk is an open source toolkit for building communications applications. For a more detailed explanation, check out the Get Started section.

For more information on how to use Asterisk, see the Configuration and Operation sections of the wiki. By providing your contact information we will be able to inform you of:. FreePBX makes it easier to build a custom phone system to fit your needs with its feature-rich core and many available modules and add-ons. Download the full ISO today to easily get started using Asterisk. As the maintainer and sponsor of Asterisk, Sangoma has used the power of open source to create an award-winning, turnkey phone system based on Asterisk that includes advanced features and requires zero coding.

If you need additional information about installing Asterisk from source code, read the installation guide on the Wiki. Code can be checked out from the Git servers via anonymous read-only access.