Installing formica




















Use a Roller to apply concentrated pressure all along the newly glued formica strip. If you don't have a roller you can use a sturdy toy car with wheels that are soft enough to not scratch the formica.

Trimming the overhanging drip edge must be done before the table top or counter top can be laminated. Use the laminate router to trim the overhanging formica. Make sure there are no little bumps that will hold up the edges of the counter top. The surface of the countertop substrate must be perfectly flat with not bumps that will hold the formica sheet off and not allow the glue to adhere the two surfaces together.

Use a grit sanding block to sand off any glue residue or other particles. Wipe the surface with a clean rag. Apply an even coat of glue to both the top of the countertop substrate and the bottom side of the Formica sheet according to the manufactures recommendation on the can.

Let it dry until it is no longer sticks to your finger when you touch it. Position the sheet of formica above the countertop substrate. Hold one end up high and the other end close to where it will be installed making sure it is lined up correctly. Once you start sticking one end the rest of the formica sheet will follow the same angle, you will not be able to take it off and reposition it.

Attach the one end and then work your way across the sheet laying down the formica as you go. The only difference now will be the possibility of the router cutting the surface of the drip edge. This happens when the router is not held flat on the surface or the drip edge is not cut perfectly square. If the router is scraping the surface of the drip edge then you can use a scrap piece of laminate to hold up the router base plate as shown in the picture.

The edges may be softened up a bit by using a file. This takes off any sharp edges created by the router. Be careful to not remove too much material. FAQ Customer Kudos. How Tall Is My Shed? What Happens After I Order? Measure the areas that you want to cover and then add about one inch to each dimension so you can be sure that the formica will extend past the edge when it is first glued on, before it is trimmed.

Take into consideration any design on the formica. A design such as a wood grain formica will need to be installed in a certain direction so the wood grains line up. This means that you can't always just use just any piece because you need to consider the size of the piece and the grain or pattern direction.

To cut with a laminate trimmer: Lay the sheet of formica on a flat working surface with a straight edge. Learn why people trust wikiHow. Download Article Explore this Article methods.

Tips and Warnings. Things You'll Need. Related Articles. Article Summary. Method 1. Select the correct Formica or other laminate for your project. Most places that sell laminate will provide sample chips for you to take home and compare to the house's color scheme. Take several of these home and test for additional properties to help you decide. A matte finish will hide wear and tear better than a glossy laminate, which is easily scratched, but may require more cleaning.

Laminates come in a whole spectrum from the most glossy to the most matte, so consider each chip by its appearance, and not its marketing. Test how well the laminate stands up to wear and tear by scratching it with a steak knife. Lightly sand the surface on which you will install the Formica. Sand the surface to create a rough surface for solid adherence, and wipe away sawdust with a tack cloth or damp rag.

If the surface is covered by paint or varnish, you should sand thoroughly to remove it using coarse or medium coarse sandpaper. Measure the length and width of the areas where you will install Formica. Use a tape measure to get an accurate measurement of each dimension of the area. If you are installing a full countertop and your walls are not at perfect right angles, you should scribe the Formica first.

See Troubleshooting for more information. Place the Formica on a flat, stable surface. This should be large enough to keep the Formica steady while cutting. Use scrap plywood or similar material that you don't mind damaging with the saw. Don't cut on concrete or another surface that will damage the saw blade. Mark the measurements on the back of the Formica sheet, adding 1 inch 2.

Draw your cut lines onto the laminate at the increased measurement, which ensures you don't waste a large piece of laminate due to cutting too small a piece. Apply masking tape along the lines. This makes it easier to see where to cut, while also reducing the risk of chips.

You can also apply additional tape to the surface beneath the formica to protect it, but you shouldn't cut over a surface you want to keep presentable. Cut the Formica along straight lines. Ideally, you should use a circular saw, saber saw, back saw, table saw, or laminate shears. A handsaw with at least 10 teeth per inch 4 per cm will also work, but may be tedious for larger jobs.

If you don't have a saw, use a craft utility knife with a laminate cutting blade to score the laminate sheet, and then snap it on the scoring by lifting the smaller piece until it snaps. Use a straightedge to keep your score straight. Lift carefully and keep an eye on the score to make sure the laminate bends at the desired break point. Do not use these tools to make circular cuts. Cut out the laminate piece in straight lines, taking care not to cut into the marked area.

Use a different tool to make curved adjustments if applicable. If your installation place is curved, you'll need to use a jigsaw or laminate router to make these finer adjustments. The cutting tool you used earlier will have trouble turning along a curve, resulting in laminate that won't fit. Method 2. Apply contact cement to the edge strip and the surface it will attach to if applicable. If you are installing laminate on a countertop or other surface with edges, begin with the edge pieces.

If you cut them from the laminate yourself, apply the contact cement with a brush or roller to both surfaces. Allow it to set until it feels tacky, according to the manufacturer's directions.

If you are using pre-glued end caps , all you need to do is heat a clothes iron, place the laminate against the edge, and iron back and forth. Let sit for one minute and gently tap it along its length with a rubber mallet or shoe heel. You can now skip to Trim the edge strip. Align the edge strip to the surface carefully. When you are sure you have it placed properly, press it to the surface. Press the Formica with a roller.

Push a dry roller back and forth across the laminate to adhere it completely and to remove air from between the laminate and the surface. Trim the edge strip if applicable. Use a fine file to remove the excess material, applying pressure only on the up strokes.

You may use a laminate trimmer or router instead, but if you do you should lubricate the edge with petroleum jelly Vaseline first. Use a carbide drill bit when trimming laminate. Cover the trimmed edges with painter's tape. Before continuing, protect your finished edges while you install the remainder of the laminate sheet.

Spread contact cement on the surface and the Formica with a paintbrush or roller. Allow it to set according to manufacturer's instructions. As a general rule, the contact cement should be left until it becomes tacky and dry to the touch, but no longer.

Often, these adhesives activate when moistened with water. Align the surface carefully using dowels. These should lay flat across the full width of the surface to hold the laminate up until it is aligned.

When applying laminate to vertical surfaces, you will need to position them by hand. Position the laminate sheet and press it one area at a time. Align the laminate as accurately as you can, then continue to adjust it as you move from one end of the surface to the other. Shift the dowels out of the way once you've aligned each section, then press it down to adhere it to the surface. Roll over the installed laminate. Push a roller across the sheet to eliminate air pockets and strengthen the contact bond.

Trim and shape the edges with a laminate trimmer or other router. Use a flush trim carbide drill bit. Stop frequently to allow the router to cool, as the laminate will melt if exposed to high heat.

File down the sharp edge. Use a fine wood file to methodically file down the sharp edge of the laminate. File downward at an angle along the entire edge. Method 3. Before installing, scribe your countertop to adjust it if it won't fit. If your walls are not at right angles, place your countertop against the wall as closely as you can, then use a compass and sander to adjust the shape: [7] X Research source Check that the countertop is level using a plumb bob or level.

Slide shims or wedges beneath the countertop to make it level if necessary. Hold the non-pencil end of the compass against the wall at the widest gap, and touch the pencil end against the countertop. Move the compass along the length of the wall to draw a line on your counter. Clamp the countertop onto a sawhorse or other secure position, then use a sander or block plane to level the countertop up to the pencil line. Your countertop should now fit snugly against the wall.

Install angled edges of Formica using miter bolts and sealant. Attach these diagonal pieces together with miter bolts after aligning their front edge. Apply a bead of sealant or laminate caulk to ensure a waterproof corner. Do not over tighten the miter bolts. Only tighten enough to keep the pieces in place.



0コメント

  • 1000 / 1000